MatthewKuKanich/CAN_Commander
CAN Commander is a comprehensive tool designed for the reverse engineering of CAN (Controller Area Network) bus systems. This project aims to provide a robust platform for automotive enthusiasts, engineers, and security researchers to interact with and analyze CAN networks, facilitating a deeper understanding and manipulation of communication.
🔌 Reverse engineering CAN bus trên Flipper Zero với ESP32
Một bộ công cụ hoàn chỉnh biến Flipper Zero thành thiết bị phân tích và tiêm lệnh trên bus CAN ô tô, chạy firmware ESP32 qua UART.
CAN Commander là ứng dụng Flipper Zero (firmware ESP32) chuyên dụng cho việc reverse engineering và thao tác trên bus CAN (Controller Area Network) — giao thức truyền thông nội bộ trong xe hơi. Ứng dụng giao tiếp với board CAN Commander qua UART, cho phép người dùng đọc/ghi frame, chẩn đoán OBD2, và tiêm lệnh trực tiếp lên bus. Phiên bản hiện tại v2.3.1, yêu cầu firmware ESP32 tối thiểu v2.2.
✨ Điểm nổi bật
- Monitor & Discovery: Đọc toàn bộ frame trên bus hoặc lọc theo ID/mask để theo dõi ECU cụ thể khi read-all quá nhiễu
- Vehicle Diagnostics: Hỗ trợ OBD2 Live Data (PID List), Fetch VIN, Fetch DTCs, Clear DTCs — quét mã lỗi và reset check engine light
- Smart Injection: Lưu dữ liệu live của các ID đang theo dõi, sau đó chỉ thay đổi bit/trường cụ thể trong frame — giữ nguyên mọi tín hiệu không muốn đổi, tránh gây lỗi hệ thống
- Filter & Read Frames: Bộ lọc linh hoạt với bus, mask, filter, ext_match, ext — giảm nhiễu khi cần tập trung vào một thông điệp nhất định
- Write/Inject Frames: Tiêm frame xác định với đầy đủ tham số bus, id, ext, dlc, data, count, interval_ms — hỗ trợ resend nhanh bằng OK
- Replay: Ghi và phát lại frame CAN đã bắt, hữu ích cho kiểm thử và phân tích chuỗi lệnh
- Profile hệ thống: Lưu cấu hình dưới dạng
.injprofvà.dbcprof, load lại cho các phiên làm việc sau - WiFi CLI over TCP: Điều khiển từ xa qua TCP khi kết nối WiFi
💡 Vì sao đáng chú ý
CAN Commander không chỉ là một tool đọc dữ liệu xe — nó xây dựng cả workflow từ giám sát → phân tích → tiêm lệnh một cách an toàn. Điểm mạnh nhất nằm ở Smart Injection: thay vì gửi frame thô có thể làm hỏng tín hiệu đang hoạt động, ứng dụng ghi lại dữ liệu real-time, giữ nguyên các bit không đổi, và chỉ thay thế đúng trường cần thiết. Điều này biến việc tiêm lệnh từ "rủi ro cao" thành thao tác kiểm soát được.
Dự án phù hợp cho automotive enthusiasts, kỹ sư embedded, và security researchers muốn nghiên cứu giao tiếp CAN trên xe. Workflow được thiết kế rõ ràng từ read traffic cơ bản đến diagnostic và injection nâng cao, có thể bắt đầu bằng một read test đơn giản rồi tiến tới cấu hình profile phức tạp.
#CANBus #ReverseEngineering #AutomotiveSecurity #FlipperZero #TiniX
Similar Projects
Discover other similar projects and AI models.
CAN Commander is a comprehensive tool designed for the reverse engineering of CAN (Controller Area Network) bus systems. This project aims to provide a robust platform for automotive enthusiasts, engineers, and security researchers to interact with and analyze CAN networks, facilitating a deeper understanding and manipulation of communication.
Tesla Mod — Flipper Zero & ESP32. Nag killer, FSD region unlock, track mode, BMS dashboard, blind spot alert, high beam strobe, CAN capture, steering mode + more. Works via OBD-II or X179 connector.
Open-source browser-based CAN bus analyzer. Works with low cost USB hardware.
The Dom amongst the Flipper Zero Firmware. Give your Flipper the power and freedom it is really craving. Let it show you its true form. Dont delay, switch to the one and only true Master today!